Photonic Solutions Enewsletter

February 2019

Quick Tip: Surface-Enhanced Raman Scattering Sensors

Surface-Enhanced Raman Scattering (SERS) sensors continue to attract attention as an analytical technique for chemical sensing and biomedical applications. SERS sensors offer multiple analysis advantages, including easy operation without complicated sample preparation, single-molecule sensitivity, high throughput, and point-of-care applications from commercially available portable Raman spectroscopes. Electric and magnetic field enhancements from localized surface plasmon (LSP) effects can reach several orders of magnitude higher than the incident field; this enhancement is preferred in most SERS sensors. The design and fabrication of plasmonic nanostructures is the key for high-performance SERS sensors, since the maximum field enhancement determines the sensors’ sensitivity, reproducibility, and applicability. [1]

One of the unique features of SERS sensors is that an analyte can be identified by its unique Raman spectrum, providing a route for label-free detection. Unfortunately, Raman scattering itself is inefficient because of the small scattering cross section. However, the analyte’s low scattering cross section can be overcome by designing plasmonic structures to either enhance the intrinsic SERS signal of the analyte, or use an extrinsic design where the SERS signal of a reporter molecule is only enhanced in the presence of the analyte.  Figure 1 demonstrates the ability of this type of biosensor to measure the level of vascular endothelial growth factor (VEGF) in clinical blood plasma samples taken from breast cancer patients. [2]

Figure 1. Schematic illustration of SERS immuno-sensor for biomarker operating detection

We have created a system to imitate this type of sensor to show surface plasmonic nanostructure enhanced Raman effects, as shown in Figure 2. A thin layer of Au is deposited on a Si substrate.  A hexagonal array of air holes in the Au film forms bow-tie-shaped sharp metal edges, which will create a strong LSP EM field when illuminated. A hexagonal array of silver plasmon nanoprobes are placed on top of the Au film. The nano probe is used as the analyte, which can effectively adjust the scattering peak spectrum (see "RSoft Application Gallery Note: Plasmon Nano Probe"). A nanorod array is used as the “reporter molecule” in this structure. Its index, shape, and material properties will directly report the outputs detected.  

Figure 2. A mimic structure for surface-enhanced Raman sensor

We have performed CW simulations for this structure with the RSoft FDTD tool, FullWAVE, at a wavelength of 0.54um with periodic boundary conditions. The period is that of the LSP triangular array.  The third-order nonlinear responses χ(3) of gold and silver are on the order of 8×10-19 (m/V)2 and 2×10-19 (m/V)2, respectively.  A 5x109 V/m strength electric field is incident on the structure. The reflected power is monitored and its spectrum, derived from FFT calculation, is outputted.  

Figure 3. Simulation results show strong Raman scattering with LSPs

Simulation results are shown in Figure 3. Significant Raman scattering peaks appear for the patterned gold film due to the strong LSP fields created. On the other hand, the flat gold film doesn’t show any Raman scattering. Different indexes of the reporter material shift the Raman scattering peaks.    

Note that we used Method 3 described in Appendix D of the FullWAVE manual to set up the nonlinear simulation. The normalized χ(3) is related to the incident electric field. 

Download Design Files


  1. Ming Li, Scott K Cushing and Nianqiang Wu. “Plasmon-Enhanced Optical Sensors: A Review”, Analyst. 2015 Jan 21; 140(2): 386-406.
  2. Ming Li, Scott K Cushing,etc. “Three-Dimensional Hierarchical Plasmonic Nano-Architecture Enhanced Surface-Enhanced Raman Scattering Immunosensor for Cancer Biomarker Detection in Blood Plasma”, ACS Nano, 20137 (6), pp 4967–4976.

Photonic Integrated Circuit (PIC) Training Silicon Valley

Annual PIC Training by Synopsys

March 19-22, 2019
Sheraton Brussels Airport Hotel
Brussels, Belgium 

Join us for a four-day training on photonic design for photonic integrated circuits (PICs). The training is aimed at application and R&D engineers as well as managers interested in understanding the development of PICs and the role of software automation in their design, simulation, and fabrication procedures.

This training will feature live training and hands-on demonstration of the Synopsys PIC Design Tools for PDK-driven PIC design. During the hands-on session, attendees will have the opportunity to work directly with the software under the guidance of technical staff from the company.

Calendar of Events

For the latest event calendar, please go to our Events page.